Bluelab pH Controller Wi-Fi
Item No.
09-445-315
The Bluelab pH Controller Wi-Fi automatically tracks and adjusts the pH levels in your reservoir, thus ensuring ideal conditions for nutrient uptake. With no need for spot checks and manual adjustments you can save time without compromising on plant health. With built-in Wi-Fi capability, if enabled
Read full description
Description
The Bluelab pH Controller Wi-Fi automatically tracks and adjusts the pH levels in your reservoir, thus ensuring ideal conditions for nutrient uptake. With no need for spot checks and manual adjustments you can save time without compromising on plant health. With built-in Wi-Fi capability, if enabled the Bluelab pH Controller Wi-Fi can display data in Edenic (an online software platform, visit Edenic.io for more information). Realtime monitoring, control, alerts, and insights right on your phone allow you to truly manage your growing environment from where you like when you like. The Controller can adjust the pH up (more alkaline) or down (more acidic) dependent upon the requirement of your growing setup. Probes constantly monitor nutrient solution pH level and temperature. The Controller doses the reservoir with pH Up or Down stock solution, by means of a peristaltic pump, on your chosen schedule, ensuring that the dose is fully mixed and readings stable before dosing again Doses are automatically compensated for temperature. Discreet visual alarms on the display will indicate if the pH level is beyond the desired range as set by the user, and dosing will not occur whenever the Controller is in alarm mode. Probes and peristaltic pump are replaceable when necessary. Powered from mains electricity via universal adaptor plug.
Key selling points:
Technical Specifications:
Control parameter: pH – user selectable single direction (up or down)
Control Range: 0.1 - 13.9 pH
Dose rate: 120 ml per minute
Resolution: 0.1 pH
Accuracy at 25 °C / 77 °F: ± 0.1 pH
Calibration: Two or three point (pH 7.0 and pH 4.0, and/or pH 10.0)
Temperature compensation: Yes (if temperature probe is in the same solution as pH probe)
Operating environment 0-50 °C / 32 – 122 °F
Power source:
Screen display languages: English, Deutsch, Español, Français, Nederlands
Certifications:
System requirements:
Moisture Exposure: Not IP rated. Indoor installation recommended, outdoor installation should provide protection from moisture ingress via separate enclosure or rain cover.
Altitude: Less than 2000m
Humidity: 5-95% relative humidity
Pollution dergree of the intended environment: Pollution degree 2
FAQs:
Q: Can I use the Bluelab pH Controller Wi-Fi without enabling Wi-Fi?
A: Yes, it will work just the same as a regular BlueLab pH Controller. But the advantage of Wi-Fi is that with Edenic downloadable software you can monitor and adjust the controller remotely.
Q: What are the safety lockouts to prevent overdosing??
A: The Controller will not dose if:
A: Adjust the OnTime such that 3 to 5 doses shifts the pH by only 0.1 pH. Consult your user manual for more detail on this.
Purchase this with…
09-445-905 – Bluelab Probe Care Kit - pH
09-445-935 – Bluelab Ph 4 Calibration Solution 500ml. (carton of 6)
09-445-955 - Bluelab Ph 7 Calibration Solution 500ml. (carton of 6)
09-445-805 – Bluelab pH Probe – 2m
09-445-825 – Bluelab Temperature Probe
09-445-860 – Bluelab Power Supply for pH Controller and Pro Controller International Plugs
09-445-875 – Pump Cassette only for Peripod M3/M4 and pH Controller
Key selling points:
- View your reservoir pH on your mobile phone no matter where you are
- Automate pH control in reservoirs of up to 200 US gallons/760 litres
- 10 ml/min peristaltic pump delivers precise control
- Controls pH in the up (alkali) or down (acid) direction
- In-built safety lockouts prevent overdosing
- Dosing routine allows for effective mixing before next dose
- Auto-resume dosing when restarting after power loss
- High and low alarms to alert you when pH is out of range
- Acid- and alkali-resistant delivery tubing
- 2-metre/6-ft probe and power cable lengths and 4-metre/13.12-ft total tubing for best positioning and viewing
- Flexible mounting options for walls, posts and racks
- Easy-to-clean display built for clean environments
- Easy access to Edenic software (downloadable from Edenic.io)
Technical Specifications:
Control parameter: pH – user selectable single direction (up or down)
Control Range: 0.1 - 13.9 pH
Dose rate: 120 ml per minute
Resolution: 0.1 pH
Accuracy at 25 °C / 77 °F: ± 0.1 pH
Calibration: Two or three point (pH 7.0 and pH 4.0, and/or pH 10.0)
Temperature compensation: Yes (if temperature probe is in the same solution as pH probe)
Operating environment 0-50 °C / 32 – 122 °F
Power source:
- Input: 100-240 Vac, 50-60 Hz, 5 VA
- 4 Interchangeable plug types (USA, Euro, UK, NZ/AUS)
- Output 24 V DC 0.4 Amp
Screen display languages: English, Deutsch, Español, Français, Nederlands
Certifications:
- CE, FCC, IC. Contains Wi-Fi/Bluetooth Module
- IC: 21098-ESPS3WROOM1, FCC
- ID: 2ACZ7-ESPS3WROOM1
- Indoor / Urban: Up to 20 metres / 66 feet
- Outdoor / RF line-of-sight: Up to 50 metres / 164 feet
System requirements:
- Android (8.0 or later) or iOS (12 or later) Mobile phone for Edenic Software.
- Internet connection for remote access & data-logging.
Moisture Exposure: Not IP rated. Indoor installation recommended, outdoor installation should provide protection from moisture ingress via separate enclosure or rain cover.
Altitude: Less than 2000m
Humidity: 5-95% relative humidity
Pollution dergree of the intended environment: Pollution degree 2
FAQs:
Q: Can I use the Bluelab pH Controller Wi-Fi without enabling Wi-Fi?
A: Yes, it will work just the same as a regular BlueLab pH Controller. But the advantage of Wi-Fi is that with Edenic downloadable software you can monitor and adjust the controller remotely.
Q: What are the safety lockouts to prevent overdosing??
A: The Controller will not dose if:
- The temperature probe measures a solution temperature of less than 0 °C / 32 °F or more than 50 °C / 122 °F
- The pH reading does not change after 15 dose cycles
A: Adjust the OnTime such that 3 to 5 doses shifts the pH by only 0.1 pH. Consult your user manual for more detail on this.
Purchase this with…
09-445-905 – Bluelab Probe Care Kit - pH
09-445-935 – Bluelab Ph 4 Calibration Solution 500ml. (carton of 6)
09-445-955 - Bluelab Ph 7 Calibration Solution 500ml. (carton of 6)
09-445-805 – Bluelab pH Probe – 2m
09-445-825 – Bluelab Temperature Probe
09-445-860 – Bluelab Power Supply for pH Controller and Pro Controller International Plugs
09-445-875 – Pump Cassette only for Peripod M3/M4 and pH Controller
Specifications
UK RRP | £479.00 |