Español
Français
RAM Combi-Duct Lightproof Ducting - 152mm x 5m
Item No.
08-360-260
A 4-layer multi-laminated ducting with an encapsulated high tensile steel wire helix which holds the open round shape of the duct to give less drag than competitor products, and thus less noise and less pressure drop in service. The aluminium and polyester inner layers minimise noise, while the
Read full description
Description
A 4-layer multi-laminated ducting with an encapsulated high tensile steel wire helix which holds the open round shape of the duct to give less drag than competitor products, and thus less noise and less pressure drop in service. The aluminium and polyester inner layers minimise noise, while the tough black PVC copolymer outer acts as a vapour and light barrier and improved airtightness while remaining flexible. Totally plant safe. Supplied individually boxed in a 5m length. In the event of a fire, RAM Combi-Duct will emit no toxic gases.
Key selling points:
Technical Specifications:
FAQs:
Q: How should I install my ducting for best ventilation system performance?
A: All systems differ, but there are some basic guidelines which you should follow when designing your system:
Purchase this with…
Key selling points:
- Ducting holds its open round shape in all conditions
- Lightproof, low-noise and plant safe
- Fits to round inlet/outlet spigots of fans, filters or junctions
- Easily cut to length without special tools
- Seal joints with standard clamps or duct tape
- Fire resistant – will not emit toxic gases in case of fire
- Noncorrosive to common metals
Technical Specifications:
- Nominal diameter: 150mm (6”)
- Material: Aluminium/polyester laminate with high-tensile steel helical wire reinforcement and PVC copolymer outer
- Temperature range in service: -30°C - 120°C (-22°F - 248°F)
- Maximum air velocity: 30 m/s (98.4 ft/s)
- Maximum positive air pressure: 2500 Pa (0.36 psi)
- Supplied length: 5m (16’ 5”) compressed to 0.5m (19.7”)
FAQs:
Q: How should I install my ducting for best ventilation system performance?
A: All systems differ, but there are some basic guidelines which you should follow when designing your system:
- Avoid excessive lengths of duct. Ducting lengths should be taut when installed
- Support ducting adequately. Don’t allow it to dangle over beams or hangers and become kinked
- Keep any bends as gradual as possible. The inside radius of any bend should always be larger than the duct diameter – ideally much larger.
- If you need a tight bend, use a pressed metal bend
- When joining duct lines, use a straight joiner, a tee or Y connector as required
- Clamp all joints tightly to avoid leaks, and seal with duct tape.
Purchase this with…
- 08-330-215 - Ducting Tee Connector - 150mm
- 08-330-315 - Ducting Y Connector - 150mm
- 08-330-415 - Ducting Wall Flange - 150mm
- 08-330-465 - Square Backed Flange - 150mm
- 08-330-515 - Male Ducting Joiner - 150mm
- 08-330-565 - Female Ducting Joiner - 150mm
- 08-330-615 - Ducting Back Draft Damper Joiner - 150mm
- 08-330-715 - Ducting Pressed Bend 90 Degrees - 150mm
- 08-360-215 - RAM Combi-Duct Lightproof Ducting - 152mm x 10m
- 08-365-015 - 60-215 Quick Release Clamp (8")
- 08-370-005 - 2" Cloth Duct Tape - 48mm x 50m
- 08-395-015 - Flexible Silencer 150mm (6")
Specifications
| UK RRP | £15.60 |